LITHIUM CORDLESS SCREWDRIVER PAS 3.6 A1 LITHIUM CORDLESS SCREWDRIVER Operation and Safety Notes Translation of original operation manual LITIUM-AKKURUUVINVÄÄNNIN Käyttö- ja turvaohjeet Alkuperäisen käyttöohjeen käännös SLADDLÖS SKRUVDRAGARE PAS LITHIUM Bruksanvisning och säkerhetsanvisningar Översättning av bruksanvisning i original LITHIUM-BATTERIDREVET SKRUETRÆKKER Brugs- og sikkerhedsanvisninger Oversættelse af den originale driftsvejledning LITHIUM-AKKUSCHRAUBER Bedienungs- und Sicherheitshinweise Originalbetriebsanleitung 3 Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device. Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin. Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med apparatens / maskinens funktioner. Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner. Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. GB / IE FI SE DK DE / AT / CH Operation and Safety Notes Käyttö- ja turvaohjeet Bruksanvisning och säkerhetsanvisningar Brugs- og sikkerhedsanvisninger Bedienungs- und Sicherheitshinweise Page Sivu Sidan Side Seite 5 13 21 29 37 1 2 3 9 4 8 7 6 5 A 9 8 1 B 10 C D E Table of contents Introduction Intended purpose ..........................................................................................................Page Equipment Components ................................................................................................Page Included items ...............................................................................................................Page Technical Data ..............................................................................................................Page 6 6 6 7 General safety advice for electrical power tools 1. Workplace safety .....................................................................................................Page 2. Electrical safety .........................................................................................................Page 3. Personal safety..........................................................................................................Page 4. Careful handling and use of electrical power tools ...............................................Page 5. Use and handling of the cordless electrical power tool ........................................Page Safety advice relating to cordless drill drivers ............................................................Page Original ancillaries / accessories .................................................................................Page 7 8 8 8 9 9 10 Before first use Charging the rechargeable battery on the device (see Fig. D) .................................Page 10 Changing the bits / screwdriver bit inserts ...................................................................Page 10 Preparing the tool for use Switching on / off the cordless screwdriver .................................................................Page Changing the direction of rotation ...............................................................................Page Switching on / off the LED lights ...................................................................................Page Tips and Tricks ...............................................................................................................Page 10 10 10 11 Maintenance and cleaning .........................................................................Page 11 Service .........................................................................................................................Page 11 Warranty ...................................................................................................................Page 11 Disposal ......................................................................................................................Page 11 Conformity Declaration / Manufacturer ..........................................Page 12 GB/IE 5 Introduction The following pictograms are used in these operating instructions / on the device: Read instruction manual! Observe caution and safety notes! Caution ­ electric shock! Danger to life! Risk of explosion! Safety class II Keep children away from electrical power tools! Wear hearing protection, dust protection mask, protective glasses and protective gloves. For indoor use only! Check that the device, mains lead and plug are in good condition! Dispose packaging and appliance in an environmentally-friendly way! Do not dispose of rechargeable batteries with your household refuse! n0 V~ V Nom. no-load speed Volt (AC) mA A / Ah Milliamps / Amps / Amp-hours Direct current (Type of current and voltage) © Lithium cordless screwdriver PAS 3.6 A1 © Equipment Components Direction of rotation switch / lock Direction indicator (clockwise) Battery display Direction indicator (anticlockwise) Charging socket (device) ON / OFF switch (LED lights) ON / OFF switch LED lights Tool holder Mains adapter Introduction Before you use it for the first time, it is essential that you make yourself fully familiar with the functions of the appliance and find out how to correctly handle electrically powered tools. To do this, read the following operating instructions carefully. Retain these instructions for future reference. Additionally, pass them on to whoever might acquire the appliance at a future date. © 1 2 3 4 5 6 7 8 9 10 © Included items Lithium cordless screwdriver PAS 3.6 A1 Mains adapter PAS 3.6 A1 - 1 Carry case Bits x 25 mm Bits x 50 mm Bit extension (see Fig. C) Operating instructions Intended purpose This device is intended for driving screws into wood, plastic and metal. Use the appliance only as described and only for the purposes indicated. The device is not intended for commercial use. Any other uses, and modifications to the appliance, are deemed to be improper usage and may result in serious physical injury. The manufacturer accepts no responsibility for damage(s) resulting from improper usage. 6 GB/IE 1 1 1 26 2 1 1 Introduction / General safety advice for electrical power tools © Technical Data PAS 3.6 A1 cordless screwdriver: Rated voltage: 3.6 V Rechargeable battery (integrated): LITHIUM Rechargeable battery capacity: 1350 mAh No-load speed: n0 200 min-1 Torque: max. 4 Nm Tool holder: 6.35 mm (1/4") PAS 3.6 A1-1 mains adapter: INPUT: Rated voltage: 230 - 240 V~ 50 / 60 Hz Rated power: 5,5 W OUTPUT: Rated voltage: Rated power: Charging time: Protection class: Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. General safety advice for electrical power tools WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. Keep all the safety advice and instructions in a safe place for future reference! The term "electrical tool" used in the safety advice refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools powered by rechargeable batteries (without a mains lead). 6,2 V 400 mA approx. 3 hrs. II / Noise and vibration data: Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically: Sound pressure level: 55 dB(A) Sound power level: 80 dB(A) Uncertainty K: 3 dB Total vibration (vector sum of three directions) is calculated in accordance with EN 60745: Screwing: Vibration emission value ah, D = 2.101 m / s2, uncertainty K = 1.5 m / s2 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. GB/IE 7 General safety advice for electrical power tools 2. Electrical safety a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances. Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. c) d) e) f) g) 4. Careful handling and use of electrical power tools a) Do not overload the device. Always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result. b) Do not use an electrical power tool if its switch is defective. An electrical power 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. 8 GB/IE General safety advice for electrical power tools tool that can no longer be switched on and off is dangerous and must be repaired. Pull the mains plug out of the socket and / or remove the rechargeable battery before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent the device from unintentionally starting. When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools ...