MULTI-FUNCTION TooL PMFW 200 Multi-funCtion tool Operation and Safety Notes MonitoiMitYÖkAlu Käyttö- ja turvaohjeet MultifunktionsVerktYg Bruksanvisning och säkerhetsanvisningar MultifunktionsVÆrktØJ Brugs- og sikkerhedsanvisninger Bedienungs- und Sicherheitshinweise Multifunktionswerkzeug Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the device. Käännä ennen lukemista molemmat kuvalliset sivut esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin. Vik ut båda bildsidorna och ha den till hands när du läser igenom anvisningarna och gör dig bekant med apparatens / maskinens funktioner. Før du læser, vend begge sidene med billeder frem og bliv bekendt med alle apparatets funktioner. , . Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut. GB / IE / CY FI SE DK GR / CY DE / AT Operation and Safety Notes Käyttö- ja turvaohjeet Bruksanvisning och säkerhetsanvisningar Brugs- og sikkerhedsanvisninger Bedienungs- und Sicherheitshinweise Page Sivu Sidan Side Seite 5 15 25 35 45 55 12 13 1 2 3 4 5 6 7 11 10 6 8 9 a b C D e F G H Table of Content Introduction Proper use .....................................................................................................................Page Features and equipment...............................................................................................Page Included items ...............................................................................................................Page Technical data...............................................................................................................Page 6 6 7 7 7 8 8 9 9 10 10 11 11 11 11 General safety advice for electrical power tools 1. Workplace safety .....................................................................................................Page 2. Electrical safety ........................................................................................................Page 3. Personal safety .........................................................................................................Page 4. Careful handling and use of electrical power tools ..............................................Page Safety advice relating specifically to this multifunction tool .....................................Page Advice on use ...............................................................................................................Page Selecting the right tool .................................................................................................Page Changing the attached tool.........................................................................................Page Place a sanding sheet on the backing plate ..............................................................Page Vacuum extraction of dust / debris ..............................................................................Page Connecting a vacuum dust extraction device ............................................................Page Assembly Bringing into use Switching On / Off........................................................................................................Page 12 Selecting the oscillation speed ....................................................................................Page 12 Maintenance and cleaning ........................................................................Page 12 Disposal ......................................................................................................................Page 12 Information Service centre ...............................................................................................................Page 12 Warranty .......................................................................................................................Page 12 Declaration of Conformity / Manufacturer .................................................................Page 13 GB/IE/CY 5 Introduction The following pictograms are used in these operating instructions / on the device: Read the operating instructions! Always heed warning labels and safety instructions! Caution - Danger of electric shock! Hazardous voltage ­ danger to life! Explosive material! n0 Rated idle running speed Safety class II Wear hearing protection, dust protection mask, protective glasses and protective gloves. Keep children away from electrical power tools! Protect electrical power tools from moisture! Risk of loss of life by electric shock from damaged mains lead or mains plug! Dispose packaging and appliance in an environmentally-friendly way! Risk of fire! V~ W Q Volt (AC) Watts (effective power) Multi-function tool Introduction edges and precise work. Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers. We will not accept liability for loss or damage arising from improper use. Not suitable for commercial use. Q Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle electrical power tools correctly. To help you do this please read the accompanying operating instructions. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation. Q Features and equipment ON / OFF switch Oscillation speed setting wheel Dust extraction port Ventilation slots Tool mount Clamping screw with washer Plunge saw blade Allen key Sanding sheet Backing plate Segment saw blade Adapter for external vacuum extraction Reducer piece Proper use The device is intended for sawing, cutting and sanding. The preferred materials on which the device can be used are: wood, plastic, drywalling, non-ferrous metals, fixings (e.g. nails, screws) and wall tiles. It is particularly suitable for working close to 6 GB/IE/CY 1 2 3 4 5 6 7 8 9 10 11 12 13 Introduction / General safety advice for electrical power tools Q Included items Multi-function tool Plunge saw blade Clamping screw with washer (prefitted) Allen key Backing plate Sanding sheets Segment saw blade Operating instructions 1 1 1 1 1 12 1 1 Q WArNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances. Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working. Technical data 180 W 230 V ~ 50 Hz n0 15.000 - 21.000 min-1 II / Rated power consumption: Rated voltage: No-load rotational speed: Protection class: Noise and vibration data: A-weighted sound levels. Sound pressure level: 85 dB (A) Sound power level: 96 dB (A) Uncertainty K < 1.5 m / s2 Wear ear protection! Evaluated acceleration, typical: Hand / arm vibration: < 2,5 m / s2 The total vibration (vector sum of three directions) is calculated in accordance with EN 60745: Sanding: Vibration emission value ah = 6.4 m / s2, Uncertainty K < 2.0 m / s2 Sawing with the plunge saw blade: Vibration emission value ah = 9.9 m / s2, Uncertainty K < 1.5 m / s2 Sawing with the segment saw blade: Vibration emission value ah = 5.0 m / s2, Uncertainty K < 1.5 m / s2 General safety advice for electrical power tools WArNING! read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE! THE TERM "ELECTRICAL TOOL" USED IN THE SAFETY ADVICE REFERS TO ELECTRICAL TOOLS POWERED BY MAINS ELECTRICITY (BY MEANS OF A MAINS LEAD) AND ELECTRICAL TOOLS POWERED BY RECHARGEABLE BATTERIES (WITHOUT A MAINS LEAD). 1. Workplace safety a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or GB/IE/CY 7 General safety advice for electrical power tools dusts. Electrical power tools create sparks, which can ignite dusts or fumes. c) Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. 3. Personal safety a) remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) Wear personal protective equipment and always wear safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury. c) Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on. d) remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury. e) Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances. f) Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts. g) If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust. 2. Electrical safety To avoid danger to life from electric shock: a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (rCD) for protection if operating the electrical 8 GB/IE/CY General safety advice for electrical power tools 4. Careful handling and use of electrical power tools a) Do not overload the device. Always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result. b) Do not use an electrical power tool if its switch is defective. An electrical power tool that can no longer be switched on and off is dangerous and must be repaired. c) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device. d) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. e) Look af ...